Fits Fuji's T70 and T75G HVLP Spray Guns
Each air cap set sold separately.
Fuji R & D utilized
computer Fluid Dynamics programs that yielded data suggesting
improvements could be made to the angles and hole sizes in the Aircap.
Once samples were made and tested, the Aircaps exceeded all
expectations. The High-Efficency Aircaps provide the user with a cleaner
spray pattern that results in less overspray and mist in the air.
A cleaner spray pattern amounts to less overspray. Less Overspray = More Savings!
Color Coding of T-Series aircap sizes is used to make aircap selection and changes much easier.
What Fuji has done is reduce the width of the
actual fan pattern. If we take a vertical pattern, the height (lets say
9) stays exactly the same, but the width of the H, compared to standard
Aircaps is much less. Whats the advantage of a thinner-width fan
pattern? Well, as you know, when you spray across a board, as you come
off the edge, particles are spraying into the air and adding to the
overspray (mist) in the air. But you have to continue holding down the
trigger until you finally pass over the edge of the board. You cannot
stop at the edge of the board but must follow through past the board.
The wider the width of the fan pattern, the longer it takes to pass off
the edge of the board. It is this extra width of fan pattern that is
adding to the number of airborne particles with each pass. It becomes
even more significant when you realize how many times you pass over the
edge of a board when spraying a cabinet or piece of furniture. The Fuji
High-Efficiency Aircap is an exclusive feature from Fuji.
#1, 0.8mm - Perfect for very fine work. Also good for small surfaces and thinner viscosity fluids. Shading stains/Inks, as well as touch-ups, zinc, dyes water-based finishes. FOR T-SERIES SPRAY GUN ONLY.
#2, 1.0mm - Great for most fine finishing including water-based/borne coatings. Allows for thinner, wet coat to be applied. Automotive enamel and marine finishes. Nitrocellulose lacquers, sealer, cellulose acrylics, synthetics, polyurethane, stains, varnish, and primers. FOR T-SERIES SPRAY GUN ONLY.
#3, 1.3mm - Similar to the #2 but with more coverage. Automotive enamel, airplane and marine finishes. Nitrocellulose lacquers, water-based finishes, varnish, urethanes, enamel, latex for louver doors, trims and cabinets, and oil based paints. FOR T-SERIES SPRAY GUN ONLY.
#4, 1.5mm - Similar to the #3 but requires less thinning. Automotive enamel, airplane and marine finishes. Nitrocellulose lacquers, water-based finishes, varnish, urethanes, enamel, latex for louver doors, trims and cabinets, and oil based paints. FOR T-SERIES SPRAY GUN ONLY.
#5, 1.8mm - Ideal for larger surfaces, and thicker layers. Catalyzed lacquers, primers, varnish, urethanes, enamel, industrial coating (higher viscosity), sealers, polyurethane, oil based paints, epoxy enamels, plastic, adhesives, floor paving paints, latex (walls), splatter paints and multi fleck paints. FOR T-SERIES SPRAY GUN ONLY.
#6, 2.0mm - Similar to the #5 but with more coverage. Ideal for larger surfaces, and thicker layers. Catalyzed lacquers, primers, varnish, urethanes, enamel, industrial coating (higher viscosity), sealers, polyurethane, oil based paints, epoxy enamels, plastic, adhesives, floor paving paints, latex (walls), splatter paints and multi fleck paints. FOR T-SERIES SPRAY GUN ONLY.
#7, 2.5mm - Suitable for even larger areas/walls & ceilings. Ideal for fast coverage. Stone finish, texture coating, industrial primers, latex (walls and ceilings), high viscosity industrial coating and nitrate dope. FOR T-SERIES SPRAY GUN ONLY.
Tip Sizes Sold Individually
California Residents
Warning Cancer and Reproductive Harm - see Prop 65 Warnings
